Chinon AVi Insturction Manual

1. Placement. To prevent fire or electric shock, do not expose this TV to rain or moisture. Do not place the set on an unstable cart, stand, tripod, bracket or table to prevent it from falling. Keep the unit away from strong magnets, heat sources, direct sunlight, and excessive dust. If the unit is brought directly from a cold to a warm location, moisture may condense inside the unit. When you move it from a cold to a warm location, wait for about one hour before operating the unit, or leave the unit turned on until the moisture evaporates.
   
2. Installation. Ensure that the TV is installed in accordance with the instructions and illustrations provided in this manual.
   
3. Caution. Do not push objects of any kind into the unit through openings; do not spill or spray liquid of any kind on or in the system (this may result in a fire or electric shock). Do not place anything heavy on the unit. To ensure proper ventilation and proper operation, never cover or block the slots and openings with a cloth or other material. Keep the unit away from an open flame such as fire, candle etc. The unit should only be serviced by authorized technical personnel.
   
4. Disassemble. Do not attempt to disassemble the cabinet. There is a risk of electric shock. Contact qualified service personnel if your system needs repair.
   
5. Cleaning. When cleaning, make sure the system is unplugged from the power source. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the TV only.
6. Do not operate or store the unit close to flammable items or liquid.

Caution!

• To avoid injury, do not connect the provided AC power adapter to a ceiling outlet.
• Using an adapter other than the one included may not meet the unit specifications and could damage the unit or the adapter.
• The center tip of the plug of the AC/DC Adaptor must be set to positive and its plug must fit the unit’s DC12V jack. The supplied AC/DC adapter meets these specifications.
• Do not leave the AC/DC adapter plugged into the AC outlet or connected to the unit when you are not using it.
• The adapter might become warm after extended periods of use.

Your remote control comes with a battery already installed. Pull the plastic tab out of the battery compartment to begin using the remote.

Replacing the Remote Control's Battery
Press the tab on the battery compartment tray, slide the battery compartment tray out, and insert a new battery plus "+" side up. Slide the tray back into the battery compartment until it clicks.

Battery Notes:

• Keep button-cell batteries away from children. Swallowing a button-cell battery can be fatal.
• Dispose of the old battery promptly and properly. Do not burn or bury it.
• Use only a fresh battery of the required size and recommended type.

1. Connect the included AC/DC Adapter to the DC12V input jack at the back of the unit and then connect it to the power source.
2. The unit can also be battery powered. Open the battery door at the back of the unit and insert eight pieces of C size batteries into the battery compartment in the polarity shown.
3. After power is connected to the unit, it will enter standby mode. The Status and Clock LCD display will turn on with dim backlight and display 12:00AM blinking. The backlight of this LCD can be turned fully on by using the BACKLIGHT key on the remote control.

1. After power is connected and the unit in standby mode, long-press the SET key on the unit or ENTER/SET button on the remote control and the hour digits will be blinking on the Status and Clock LCD Display.
2. Adjust hour setting via the «l or »l key on the unit or the LEFT or RIGHT button on the remote control.
   
3. Short-press SET key on the unit or ENTER/SET button on the remote control and the minute digits will be blinking. Adjust minute setting via the«l or »l key on the unit or the LEFT or RIGHT button on the remote control.
4. Short press SET key on the unit or ENTER/SET button on the remote control to set time.

FM Radio Operation

1. Fully extend the rod antenna at the back of the unit.
2. In FM radio mode, long-press the unit«l or »l keys or remote LEFT or RIGHT buttons to auto-search radio station.
3. Short-press the«l or »l keys on the unit or the LEFT or RIGHT buttons on the remote control to fine-tune the selected radio signal.
4. Press the SET key on the unit or ENTER/SET button on the remote control to memorize the radio channel. The memory address can be changed by the M+ or M- keys on the unit or UP/MEM+ or DOWN/MEM- buttons on the remote control.
5. The unit can memorize up to 20 radio channels.
6. Press the VOL+ or VOL- keys on the unit or the remote control to adjust the volume.

iPod Operation

1. Insert your iPod onto the docking.
2. In iPod mode, TFT LCD and iPod will be turned on.
3. Press the MENU button on the unit or the remote control to enter the iPod menu.
4. Press the M+ or M- keys on the unit or UP/MEM+ or DOWN/MEM- buttons on the remote control to select the item needed and press the SET key on the unit or ENTER/SET on the remote control to confirm the operation.
5. Press the VOL+ or VOL- keys on the unit or the remote control to adjust the volume.
6. You can also press the«l or »l keys on the unit or LEFT or RIGHT buttons on the remote control to play the next or the previous item.

1. Plug the TV antenna into the antenna socket at the back of the unit and fully extend the antenna.
   
2. Press the MENU button on the unit or the remote control and the On Screen Display (OSD) menu will appear.
   
3. The OSD menu should start at the CHANNEL Options. Press the ? key on the unit or the DOWN button on the remote control to highlight item Channel Scan in the OSD menu.
   
4. Press the > key on the unit or RIGHT button on the remote to start channel scanning automatically. You can also press the SET key on the unit or the ENTER/SET button on the remote control to do so.
   
5. When channel scanning is done, Completed Channel Scan screen will appear.
   
6. Press MENU button on the unit or the remote control to exit the OSD menu.
   
7. If the reception is poor, move the antenna to another position and try channel scanning (steps 2 to 6) again. Make sure that there is no obstacle around the antenna for good reception. Keep devices such as mobile phone and microwave oven away from the unit as they may affect reception quality. Long-press the RATIO/SIGNAL button on the remote control to display the signal strength. This will help you to select a good antenna position for best reception.
   
8. Using CH+ or CH- buttons on the remote control to sequentially select the TV channels available in your channel list. You can also use the numerical buttons to directly input channel number.
   
9. Press the VOL+ or VOL- keys on the unit or the remote control to adjust the volume.
10. You can select the audio language. Press the MENU button on the unit or the remote control. Press the > key on the unit or RIGHT button on the remote control to the OPTION category. Press the ? key on the unit or the DOWN button on the remote control until you reach the item Audio Language and then press the > key on the unit or RIGHT button on the remote control. Press the ? or ? keys on the unit or the UP or DOWN buttons on the remote control to select your desire audio language. If the desire language is not available, the primary audio language of the TV channel in play will be heard.

1. Connect your external source to the AUX socket on the back of the unit.
   
2. Select AUX mode using the FUNCTION/SNOOZE button on the unit or the remote control.
3. Press the VOL+ or VOL- keys on the unit or the remote control to adjust the volume.

Press the MUTE Button on the remote control to cut off the audio.

1. Press ALARM/OSD MENU button on the unit or the remote control. The BRIGHTNESS, CONTRAST, COLOR and SCALER adjustment options will appear on the LCD.
   
2. Press the ENTER/SET button on the remote control to scroll the items that you need to adjust.
   
3. Use the UP or DOWN buttons to adjust the value of the items selected.
4. The SCALER option allows you to change the aspect ratio of the LCD display to match that of the image being displayed. There are two options available 16:9 and 4:3.

Audio Equalizer

Audio equalizer is available to enhance the audio quality for different type of music and audio. Press the EQ button on the remote control to cycle through each of the CLASSIC, JAZZ, ROCK and POP settings. The EQ setting will be displayed on the Status and Clock LCD Display.

1. Put the unit into standby mode using the POWER button on the unit or the POWER/AL-RST button on the remote control. Press the ALARM/OSD MENU key on the unit or the remote control and the hour digits will be blinking.
   
2. Adjust hour setting via the «l or »l key on the unit or the LEFT or RIGHT button on the remote control.
   
3. Press ALARM/OSD MENU key on the unit or the remote control and the minute digits will be blinking. Adjust minute setting via the«l or »l key on the unit or the LEFT or RIGHT button on the remote control.
   
4. Press ALARM/OSD MENU key on the unit or the remote control. You can select the alarm source by pressing the «l or »l keys on the unit or the LEFT or RIGHT buttons on the remote control. With each press of these keys, the unit will cycle through each of the BUZZER(Bu)→FM Radio (rA)→iPod(IPoD)→TV(tV) on the status LCD. When the desired alarm source is reached, press the ALARM/OSD MENU key on the unit or the remote control to enable the alarm (if you just want to set the alarm without enabling it, press the SET key on the unit or the ENTER/SET button on the remote control instead).
   
5. When alarm time arrives, press the FUNCTION/SNOOZE key on the unit or the remote control for 9 minutes of the snooze function. Press the POWER key on the unit or POWER/AL-RST button on the remote control to switch off the alarm.
6. To disable the alarm, press the ALARM/OSD MENU key on the unit or the remote control.

Sleep Timer

While the unit is on, press the SLEEP button on the remote control to adjust sleep timer setting from 90→80→70→60→45→30→20→10→0 minutes.

Using the CH+ or CH- button on the unit or the remote control to sequentially select the TV channels available in your channel list.

Using the numerical buttons and ENTER / SET button on the remote control to directly input channel.

TV Sound Mode Selection

Press the AUDIO button on the remote control to select Digital TV sound mode.
Note: items available will depend on the TV sound system being broadcasted.

Display Program Information

While viewing a program, press INFO button on the remote control to display program information and press Exit on the remote control to exit this function.

Adjusting Aspect Ratio

Press RATIO button on the remote control to select the image aspect ratio you prefer. Press the button several times to cycle through the various ratios available.

Auxiliary Channel Selection

While viewing TV, press DASH button on the remote control and enter your desired channel number and station number. 

1. Go to Channel Scan item using UP or DOWN button.   
   
2. Press RIGHT button or ENTER button to start channel scanning automatically.
   
3. If you want to stop the Channel Scan during scanning, press MENU or ENTER button.
   
4. When Channel Scan is done, Completed Channel Scan screen will appear.
5. Press MENU to return to the previous menu.

1. You can use this function to scan and add channel. Go to item Channel Add using UP or DOWN button.   
   
2. Press RIGHT or ENTER to scan and add channel.  
   
3. If a channel is already scanned by Channel Scan, or stored in channel list, it will be skipped.
   
4. If you press MENU or ENTER to stop this operation, the Cancelled Add screen will appear.      
5. Press MENU to return to previous menu.

1. Go to item Channel Edit using UP or DOWN button.
   
2. Press RIGHT or ENTER on Channel Edit and the channels stored will be listed.  
   
3. Press UP or DOWN to move to the desired channel in the list.   
   
4. Press ENTER to delete the channel.
5. Press MENU to return to the previous menu.

Manual Scan

1. Press RIGHT or ENTER on the item Manual Scan.   
   
2. Press UP or DOWN to select the specific channel.    
   
3. You can view the signal strength meter to help you adjust your antenna.
   
4. Press ENTER to add the channel (good signal) or delete the channel (bad signal). 
5. Press MENU to return to the previous menu. 

1. Press MENU button.
   
2. Press LEFT or RIGHT button on remote control to highlight the OPTION menu and press DOWN button to enter menu.

Clock

1. The current time will be automatically set by DTV channel.
   
2. The correct time zone must be set for all other functions to work properly (Guide, Info, Channel banner, etc.)
   
3. Press RIGHT or ENTER on the menu Clock to highlight the Time Zone icon.     
   
4. Press LEFT or RIGHT to change the area you are in.    
   
5. Time zone sequence:
   Eastern→ Central→ Mountain→ Pacific→ Alaska→ Hawaii→ New F. Land→ Atlantic
6. Press MENU to return to the previous menu.

Aspect Ratio

1. Go to item Aspect Ratio using UP or DOWN. Press RIGHT or ENTER to select.   
   
2. Press UP or DOWN to select an available mode.      
   
3. According the selected mode, the display format will be changed.
4. Press MENU to return to the previous menu.

Language

1. Go to item Language using UP or DOWN
   
2. Press RIGHT or ENTER on the menu language to change the menu Language display.     
   
3. Press UP or DOWN to select a menu language.
   
4. According the highlighted language, all the menu display will be changed.
   
5. LGDT111 supports: English, Spanish, and French.
6. Press MENU to return to the previous menu.

Audio Language

1. Go to item Audio Language using UP or DOWN
   
2. Press RIGHT or ENTER on the menu Audio Language to select an available audio language.    
   
3. Press UP or DOWN to select your default language.    
4. Press MENU to return to the previous menu. If there are other audio languages, then the primary audio language of the channel will be heard.

Caption Select

1. Go to Caption Select using UP or DOWN.  Press RIGHT or ENTER to select Caption Options.    
   
2. Go to ACC using the UP or DOWN key if you want to display EIA-608 Caption. Use LEFT or RIGHT key to select among CC1, CC2, CC3, CC4, Text1, Text2, Text3 and Text4.
   
3. Go to DCC using the UP or DOWN key if you want to display EIA-708 Caption.
4. Use LEFT or RIGHT key to select between Standard and Custom. Select Standard to have standard caption appearance. Select Custom, if you want to customize caption appearance using the DCC View Menu. You can customize font size, font type, text color, text opacity, background color, background opacity, edge color and edge type.
5. Press MENU to return to the previous menu. 

Sleep Mode

1. Go to item Sleep Mode using UP or DOWN and press RIGHT or ENTER to select.
   
2. Press UP or DOWN key to select the Sleep Mode option required..
   
3. Select Off to turn off Automatic Sleep.
   
4. Select appropriate time to automatically turn off TV.
5. Press MENU to return to the previous menu.

Analog Audio

1. Go to item Analog Audio using UP or DOWN and press RIGHT or ENTER to select.
   
2. Press UP or DOWN to select Mono or Stereo and press RIGHT or ENTER to select.
3. Press MENU to return to the previous menu.

Lock Menu

1. Press MENU button. 
2. Press LEFT or RIGHT button on remote control to highlight the LOCK option and press DOWN button. Password prompt window will appear.
3. Enter your 4-digit password by pressing the number button on the remote control. The default code is 0000. (Remark: If you forget your password, you can press 7777 to enter the operation.)

Lock System

1. Press UP or DOWN button on the remote control to highlight Lock System and press ENTER or RIGHT button to select.       
2. If you want to use the rating control, On should be checked. Or if you do not want to use the rating control, Off should be checked.

Set Password

1. Press UP or DOWN button on the remote control to highlight Set Password and press ENTER or RIGHT button to select. Password prompt menu will appear.
2. Enter and re-enter your new 4-digit password using the NUMBER button on the remote control.

Block Channel

1. Press UP or DOWN button on the remote control to highlight Block Channel and press ENTER or RIGHT button to select. Antenna Channels list will appear.
2. Press UP or DOWN button on the remote control to highlight the channel you need and press ENTER button to block or unblock channel.

TV Ratings-Children

1. Press UP or DOWN button on the remote controller to highlight TV Rating-Children and press ENTER or RIGHT button to select.
   
2. Press UP or DOWN button on the remote controller to highlight Age or Fantasy Violence and press ENTER or RIGHT button to select. Blocking menu window will appear.        
3. Press UP or DOWN button on the remote control to select block level or unblocking.

TV Ratings-General

1. Press UP or DOWN button on the remote control to highlight TV Rating-General and press ENTER or RIGHT button to select.
   
2. Press UP or DOWN button on the remote control to highlight Age, Dialogue, Language, Sex or Violence, and press ENTER or RIGHT button to select. Blocking menu window will appear.       
3. Press UP or DOWN button on the remote control to select block level or unblocking.

Movie Rating

1. Press UP or DOWN button on the remote control to highlight Movie Rating and press ENTER or RIGHT button to select. Blocking menu window will appear.               
2. Press UP or DOWN button on the remote control to select block level or unblocking.

Downloadable RRT

1. Press UP or DOWN button on the remote control to highlight Downloadable RRT and press ENTER or RIGHT button to select. Region rating table window will appear.
   
2. Press UP or DOWN button on the remote control to select your wanted item.

75 OHM